BEHSAN Waterproof Nano Varnish for Exterior

Solvent- base exterior wood nano varnish

  • Transparent
  • Nanotechnology
  • Water proof
  • Allows wood to breathe
  • Flexible layer on wood
  • UV resistant
  • Resistant against mould, algae
  • Does not crack, peel or blister
  • Applied by brush/cloth/dipping
  • Ready to use

 

General features:

  • Transparent
  • Nanotechnology
  • Water proof
  • Allows wood to breathe
  • Flexible layer on wood
  • UV resistant
  • Resistant against mould, algae
  • Does not crack, peel or blister
  • Applied by brush/cloth/dipping
  • Ready to use

Where to Use:

  • Suitable for all exterior wood except floors
  • Doors and window joinery
  • Shutters
  • Cladding
  • Fences
  • Pergolas
  • Balcony railings
  • Roof fringes

Packaging:

  • 0.75 L.
  • 4 L.

Non color and Pigment

Gloss:  include matt and semi gloss 

Coverage:

  • 1 L. covers 8-10 m² with 2 coats

Surface Preparation:

  • Remove any dirt, oil and wood dust from the surface.

 

New Wood Surfaces:

  • Sand the surface with sandpaper #80/120.
  • Thoroughly clean the generated dust.

 

Old Uncoated Wood Surfaces:

  • Sand the weathered surface with sandpaper #80/120.
  • Thoroughly clean the generated dust.

 

Coated Wood Surfaces:

  • Do not apply the product directly on pre-coated surfaces.
  • Remove the old paint/varnish from the surface completely with a sandpaper.
  • Thoroughly clean the generated dust.

Application:

  • The product is ready to use and does not require thinning.
  • Stir the product thoroughly before use and check its homogeneity. Repeat this process during the application.
  • Apply the product in 2 coats by brush and wait 24 hours between coats.
  • Wait 24 hours for complete dry.
  • Apply in the direction of wood grain to get a homogeneous look.

Maintenance (when the same product had been used before):

  • Do not apply the product directly on pre-coated surfaces.
  • Repeat same process as described in “Application” with 1 or 2 coats depending on weathering.
  • Clean the wood surface completely from dirt and oil and perform a slight sanding.
  • Thoroughly clean the generated dust.
  • Repeat same process as described in “Application” with 1 or 2 coats depending on weathering.
  • Inspect annually and maintain as required.

Instructions:

  • FOR EXTERIOR USE ONLY.
  • NOT SUITABLE FOR FLOORINGS.
  • Keep product closed when not in use.
  • The general application temperature of the product is between 15°C to 25°C at a relative humidity range of 40-65%.
  • The moisture content of the wood should be max. 20%.
  • Do not apply the product under direct sunlight or rain.
  • Do not apply linseed oil, basecoat/primer, yacht varnish before or after BEHSAN nano varnish for wood applied surfaces.
  • The product should be stored at temperatures between 5°C to 35°C.
  • Painting tools should be cleaned with mineral spirits after the application.

Safety Precautions:

  • USE WITH ADEQUATE VENTILATION.
  • KEEP OUT OF REACH OF CHILDREN.
  • Do not transfer contents to other containers for storage.
  • Do not use empty cans for other purposes.
  • To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
  • Avoid contact with eyes and skin.
  • Wash hands after using.
  • FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
  • Dispose of contents/cans in accordance with national regulations.
  • Please refer to the Safety Data Sheet (SDS) of the product for health and safety information.

Certificates:

  • Nano Scale Standard INSO 21145 and ISO/TS 80004 from INIC
  • ISO 14001:2015 Environmental Management System by TUV WORLD
  • ISO 9001:2015 Quality Management System by TUV WORLD